#Wifi temp monitor manual
#Wifi temp monitor for android
#Wifi temp monitor Bluetooth

Restarting hardware fixes a lot of problems - reboot your Hub, your network router and any range extenders.Make sure your router is broadcasting a 2.4GHz network. The Hub only connects to 2.4GHz band networks.

#Wifi temp monitor Bluetooth

If you get a 'Hub not connected' error message in the app, see Bluetooth connection issues.

#Wifi temp monitor manual

If your network has apostrophes or other special characters, change the name of the network, removing these characters and try entering the SSID through Manual Setup again.

Hidden Network?: choose Manual Setup and enter the SSID.

If none of this helps, and you can confirm your network is broadcasting, choose Manual Setup and enter the SSID.

Reboot your Hub and your WiFi router as well as any range extenders.

The Hub does not require large or fast data transfer. The HUB only communicates on a 2.4GHz network which offers greater range than 5GHz.

Make sure your router is broadcasting a 2.4 GHz band network.

Tap 'Refresh' in the top right on the WiFi Setup screen in the Tempest app.

If you are having trouble locating your WiFi network, try the following suggestions. Hub WiFi Connection Troubleshooting View all error codes WiFi network is not found (This could be determined if the Hub's LED is blue but the app is completely closed on your device).

Disable Bluetooth on other nearby devices which the Hub might be connecting to.

Do not try to manually pair the Hub to your device through Bluetooth settings.

Enable Bluetooth and make sure the app has permission to use Bluetooth on your device.Īndroid device users must enable location services for Bluetooth connectivity.

Wait a minute for it to reboot, then reopen the app and proceed with initial setup.

Close the app, unplug the Hub for 10 seconds and plug it back in to power cycle the device.

If you are getting a 'Hub not found' error message, this means the app is not detecting a Bluetooth connection between the Hub and your smartphone or tablet. Bluetooth Connection Troubleshooting Mobile app connection to Hub - 'Hub not found' The Tempest device can charge sufficiently within a few hours. Make sure the device is turned on and place it outdoors with the solar panels facing towards the sun. If the LED on the base of the unit is not illuminating at all, there could be a low battery issue. Continue with the setup procedure in the app.

After a few seconds the LED will slowly blink green, indicating it is ready to pair to a Hub.

On the base of the device, press and hold the clear button next to the power switch until the LED flashes.

Pairing mode is indicated by a slow blinking green LED on the base of the unit. The Tempest device must be in pairing mode before connecting to the Hub. It's unlikely, but possible the Hub has connected to another BLE device nearby, laptops, computers, smart watches, etc.

Disable Bluetooth on other nearby devices.

You should only have the app open on one device during initial setup.Toggle Bluetooth off on your device and then back on.Make sure the app has permission to use Bluetooth on your device.Close and reopen the Tempest Weather app. If you manually paired to the Hub, disable the pairing in your phone's Bluetooth settings. Go to Settings > scroll down and find the Tempest Weather app and enable 'Bluetooth Sharing' for the app.

For iOS devices: Make sure the app is allowed Bluetooth permission.Enabling location services is necessary to scan for Bluetooth LE devices.

#Wifi temp monitor for android

For Android devices: Enable Location Services.

Reopen the app and proceed with initial setup.

Toggle your phone's Bluetooth off and back on.

Unplug the Hub for 10 seconds and plug it back in to power cycle the device.

Close the app completely, close the app from running in the background.

If you are getting a 'Hub not found' error message, this usually means the app is not detecting a Bluetooth connection between the Hub and your smartphone or tablet. The Hub will only find and connect with 2.4GHz networks

Make sure your router is broadcasting a 2.4GHz network.

Locate the Hub closest to the master access point.

If you are using multiple access points, choose the master access point when setting up the Hub's WiFi connection.

Refresh the WiFi network list in the app.

Move the Hub closer to the WiFi access point.

If you don't see your WiFi network in the list of available networks. Initial Setup & Configuration Troubleshooting WiFi network not found

Replacing a disconnected device / swapping a new device.

Tempest device has disconnected from the Hub.

Data is not current / device is not connected.

Hub loses WiFi connection - 'Station offline'.

Mobile app connection to Hub - 'Hub not found'.